Hi everyone! We're hard at work trying to keep our community clean, so if you see any spam, please report it here and we'll review ASAP!  Thanks a million!
12,270 Users Online
  • 640,129,772 Downloads
  • 1,696,349 Wallpapers
  • 1,565,068 Members
  • 12,971,712 Votes
  • 5,965,287 Favorites
Home Groups Popular
Sign-Up For Free! Or login to your account »

dave112
Online Now
Login to Become a Fan
 
ProfileWallpapers (1)Favorites (0)Journal (40)DiscussionContact Member
Journal for dave112Journal for dave112
Jul
14
Wink
How to Remove EGR Valve Motor for ISUZU 4JJ1 Engine
This instruction show you guide on how to remove and install EGR valve motor for ISUZU 4JJ1 engine.

Related Contents:
ISUZU US-IDSS II 2023 2019 Diagnostic Software Free Download
2023 2019 Isuzu G-IDSS Export Diagnostic Software Free Download
ISUZU IDSS Adapter


Steps:
Removal:
1 Disconnect the battery cable negative terminal.
2 Disconnect the EGR valve connector.
3 Remove the EGR valve motor from the EGR valve.


Legend
1 EGR valve motor
2 Spring holder
3 Rod
4 Stopper

NOTE:
●Be careful not to damage the screw head.
●Do not damage the housing.
●Do not touch the spring holder.
●When a spacer is attached, do not remove it.
●Do not reuse old screws.(ifferent length)

Installation
1. Install the EGR valve motor to the EGR valve.
Set the connector in the same orientation as when the EGR valve motor is removed, and install the EGR valve motor together with the additional spacer and the plate.


Legend
1 Spacer (when originally attached)
2 Additional spacer
3 Plate
4 EGR valve motor
●The plate has to be installed in a certain orientation, and it should be installed with the concave facing to the EGR valve motor side.


Legend
1 EGR valve motor side
2 EGR valve side
●Tighten the screws in the order shown in the diagram.
Tightening torque: 2 N:m (0.2 kg-m/ 17 Ib:in)


NOTE:
●Do not pull out the motor shaft.
●Prevent any foreign matter from entering or attaching between the housing and the EGR motor.
●Do not damage the EGR valve motor installation surface.
●Do not damage the connector portion.
●Prevent the boot portion from touching the housing.
●Align the holes of the EGR valve motor with the screw holes on the housing for installation.

●Do not damage the screw head.
●Do not reuse old screws.
2. Connect the EGR valve connector.


NOTE:
●Confirm the direction of the connector.
3. Connect the battery cable negative terminal.
4. Tur ON/OFF the key so that the valve opening position can be learned.
5. Confirm that the DTC is not lit.

https://www.autoepccatalog.com
Times Viewed: 64Bookmark and Share
0 responses have been posted to this journal entry. Post Your Response!
Advertisement
Previous Journal Entry
How to Remove and Replace Cab Heater Controls for JCB 3CXThe cab heater controls A and associated cables are housed in the R.H. side console as shown.There are two control cables which operate the re-circulation vent and the hot water valve. Both the cables can be accessed by removing the side console instrumen...Read Previous Journal Entry >>Read Previous Journal Entry >>
Next Journal Entry
How to Perform Hydraulic System Pressure Release for Kubota U48-4This instruction show you guide on how to release hydraulic system pressure for Kubota U48-4 excavator.Kubota Diagmaster 22.08.01Kubota DST-i Diagnostic AdapterSteps:1. Place the machine on firm, level ground, lower the bucket and blade to ground level, a...Read Next Journal Entry >>Read Next Journal Entry >>

Recently Spotted Members


No members found. Be the first.